To work, you will need the following materials and tools: Squares Tessers of different size, Colors and transparency, Locks for splitting and cutting Mosaic, glue and mosaic grout, Capacitance for breeding, Syringe, Flexible piece of rubber, sponge, soft rag, match, blanks From wood, sandpaper with different grains, watman, dense felt, legs, glue "moment".
Work can be performed in two ways.
Method number 1 is the stands without plain ribs.
Preliminary preparation. On a sheet of white paper, we draw a straight angle of arbitrary length, inside which we put the first square of Tesra, followed by the next, inserting matches between them (future gap). By line, lay out the desired number of squares, be sure to fix the slit matches. Deciding with the number of tessera squares, you can calculate the size (width and height) of a wooden billet in the form of a square or a rectangle.
Since it is not necessary to accumulate the ribs, Phaneur can be used thin, but a thickness of at least 0.5 cm. From a piece of plywood, we cut the square (rectangle) of the desired size. We clean the emery paper. The top of the wooden billet, where we will stick to the tesser, process the sandpaper with a large
grain so that the surface of the tree become rough. It will improve gluing!
Go to execution. If you decide to perform a classic stand, as in photo 1, glue the squares, alternately selected colors and necessarily performing the gap matches. Misappling all the "field", leave the stand (Better for the night!) To dry. We divorce the grout in the tank to a more liquid state and with the help of a syringe, we write in the slit by approximately half. We leave the workpiece to dry out from 30 minutes. (time depends on the grout mark). Then we drag the grout in another container to the thickness of soft plasticine and with the help of an elastic piece of rubber with a slight indentation, fill all the slots. Excessive grout until it grabbed the Tesser, immediately remove a wet, but not wet sponge. After 15 minutes. - again. And so until the surface of the mosaic becomes clean.
All four ribs can also sharpen a thick grout. We apply it to the ribs like plasticine. In order to get more even, we take a flat strip of plywood (it should be a little wider by the ribs stand), we wear a plastic bag on it and apply, slightly pressing on the edge with a grout: After aligning the excess grouts, we carefully remove, and the edges of the edges are smoothing flexible rubber (thick grouting can be Lightly moisten with water).
Leave the mosaic to dry. After about an hour, first wet, and then with a dry soft rushing, we water the mosaic surface to disappear the whims. For the final drying, we put the stand in a horizontal position away from the heating devices (approximately 2 weeks),
In order not to scratch the worktop or other surface where it will be stand, From the bottom side, we glue the "moment" a piece of felt or 4 legs.
In photo 2. stand completed on concrete tile. On such a stand, we can successfully accommodate the sweaty vases with room colors. Beautiful, and the floor is protected from the leakage. The same stand, but on the slab of small sizes, can be used as a stand for an iron.
ATTENTION! For such supports, it is strictly forbidden to use plastic and plastic parts throughout the design.
From ordinary quadraticles Tessers, laying out them with alternating colors, form diagonal lines, and in the end we get a nice rhombus. Squares Tessers glue the jack, pour a very liquid grout. For this plate with a tester put in a pelvis and pour a diluted with liquid grout, periodically with hands in gloves in a stroke surface with squares. Kaima perform from rectangular parts, splitting the squares of the tessers on the part. First we glue, and then rub the thick sandy color grout. After drying the upper part of the stand on the bottom side, we glue thick felt (you can use legs).
Stand in photo 3 made of fine plywood and is intended for small objects. Blue squares as a decorating element obtained as a result of squares of squares into 4 equal parts. Ribs in the finished stand painted, blue paint for wood. Grout used white. At the bottom of the stand - a layer of felt.
Advice:
When the tessers are broken, observe the safety rules: split it in a cardboard box, putting glasses and gloves, away from children and households, as well as pets.
Kitchen chairs - create a certain atmosphere indoors, in our time there is a huge number of high-grade designer beauties. You can not buy the table, and you do not pay attention to the chairs, they are completed. For example, in the country, you have a big beautiful wooden table, and the chairs are made of red plastic, such a picture will not create the desired coziness, you get up to choose - make it easy to make it ready, by the way, the price policy on beautiful wooden chairs from 4000r. - Up to 15 000r.
Photo 1.
Photo 2.
Photo 3.
Start a discussion ...