How cool to have a comfortable and cozy corner for recreation on the summer cottage! So we built the benches of two types: portable and suspended.
Portable
A portable bench turned out easier in the assembly and durable. For this, we used wooden rails with a cross section of 30 × 40 mm, 400 mm long (28 pcs.) And 800 mm (14 pcs.), As well as racks (24 pcs.), 4 connecting pin with a length of 800 mm. In the rails, retreating 20 mm from the ends, drilled holes with a diameter of 5 mm. Inserted flexible pins from the aluminum wire in the chlorvinyl sheath of 2.5 square meters. mm, and in intermediate grooves - wooden racks with a diameter and a height of 30 mm.
All wooden parts are impregnated with a solution that is protected from dampness and storage.
They put on the grass two transverse rails with a length of 400 mm and inserted pins into the holes with a nodes at the base. On the back side of the bench put a longitudinal rail on a pin with a length of 800 mm, and with
It is two cylindrical racks. Further, alternating short (side) rails with racks (front) and long slats (rear), collected the entire design with a height of 700 mm. After installing the last rails, the protruding parts of the wire pins were bent. In the openings of the side walls inserted a seat 1200 mm long, made of 7 decks (you can simply have a wide cleaned board).
A suspension bench was very attractive. At first we picked up a shady space for her by subtree, on whose branches then it was hung.
For the assembly, wooden slats were required by cross section of zoh 40 mm, 800 mm long (9 pcs.), 400 mm (10 pcs.) And 100 mm (2 pcs.), As well as intermediate racks (8 pcs.). A steel twigs with a diameter of 4 mm with a thread m 4, sliced \u200b\u200bfrom ends for a length of about 15 mm were used as connecting pins. Studs for the back of the benches turned out to be 230 mm long (2 pcs.), For the front - 200 mm (2 pcs.).
At first they made a frame: 4 cross rails Long 400 mm fixed on 2 longitudinal rails with a length of 800 mm using screws with respectally M4 XL 10 mm (4 pcs), which were recorded at the base of the M4 nuts bench with washers at the base.
Separately assembled the seat, for which 4 longitudinal rails with a length of 800 mm with a hole with a diameter of 5 mm, made at a distance of 20 mm from the edge. In the gaps (30 mm) between the ends of the rails secured the racks. The rigidity of the mount was provided by two pins M4X240 mm with nuts M4 and washers. Placed the finished seat inside the frame.
Next collected a back and armrests, alternating longitudinal and transverse rails (by analogy with a portable bench). Drilled holes: in longitudinal (including in frame) - at a distance of 80 mm from the edges, in the transverse - 20 mm. Connected rails with a frame from behind with studs 230 mm, in front - 200 mm. Moreover, to cover the framework of the frame, the front bench instead of two racks used two rails 100 mm.
On top of the suspended bench tweed on the stud figure nuts M4 with rubberized washers. At the bottom of the studs screwed standard nuts M4 with washers.
After pre-assembly, the installation of the bench was carried out directly at the tree. The suspension served two kapron cord with a diameter of 4 mm and a length of 20 m. To protect the branches from damage, rubber gaskets were placed under the cord. For more convenient to sit, sometimes use a soft litter.
From early spring, our suspension bench is successful in children and in adults!
On a note:
The kitchen in the country is not less important than in the city, so that the hostess was comfortable in the country house to cook, the furniture for the kitchen should be selected with the mind. After all, in addition to everyday cooking, in the summer it is time for the workpieces for the winter, which means there should be everything necessary in the kitchen. The chain of the "Right Kitchens" stores will help you choose any hostess kitchen to taste and opportunities. A huge range and reasonable prices will not leave indifferent not one mistress.
Start a discussion ...