Wooden Floor Repair Technology

Wooden floors for a long time are known for their durability. But to extend their service life, you should not forget about the correct care and careful exploitation. It should be said that even with proper care, situations may arise when the repair of wooden floors. After all, over time, everything is worn out. If such a need arose, then you should not immediately hire workers. Some defects of such an outdoor coating can be eliminated independently. So, how to correctly repair the wooden floor with your own hands? Let's talk about this further.

How to eliminate scratches

The presence of scratches on wooden coatings is not uncommon. They can appear for many reasons. Most often this is due to negligence. Although scratches are capable of occurring, even if you simply push the massive table, without taking it off from the floor surface.

Technology repair of wooden floors when scratching:

1. If the crack is small, then it is often possible to close it with the help of a special pencil, and after the processed place is to apply a thin layer of varnish for floor coatings.
2. Large scratches can be treated with a putty. It is only important to choose it under the color of the floor. In addition, you need to know that the mixtures differ:

• in speed of drying
• in composition,
• by strength.

In any case, after eliminating scratches and complete heat drying, follows:

1. Remove from a damaged area dust and dirt.
2. Collect this part of the floor with emery paper.
3. Apply a layer of varnish.

Creak board

This problem is unpleasant for hearing - a frequent guest in the life of a parquet floor. In general, over the years, any wooden floor begins to creak. Most often, the creak is manifested only in a small area.

This problem is eliminated in various ways:

1. You can make a hole in the center of the damaged area. After that, the creak usually stops.
2. The creaking section of the floor can be lubricated with a special mixture. Only for this you first need to make a small hole in the parquet. In it, lubricant is fed under pressure. After that, the hole should be closed with a wooden plug. A mixture of WD-40 brand can be used as a lubricant.
3. Sometimes parquet stacked on a layer of concrete. In this case, during a symbol, you also need to make a hole. After that, a mixture of cement with water is poured into it (in proportion 1: 1). For the same purpose, you can still use a special composition based on hot wax.
4. In rare cases, the creak is observed throughout the wooden floor area. Then it will be necessary to completely sort out the coating.

Hipsted on a wooden floor of the water

Such situations are quite common. Wood, as you know, has a property to expand when moisture absorbing. This property on the parquet leads to its swelling. By deciding how to eliminate this problem, it is necessary to consider:

1. Wood floor laying method.
2. The size of the site on which water got.

Advice:

1. If the water fell only to several slats, then it may be easier and cheaper will simply replace them.
2. In some cases, parquet after drying is exposed to deformation. In such situations, you can rebuild the available coating or put a new one. Here everyone decides himself what will be made more profitable.
3. If large areas are flooded, then, as a rule, you have to restore them.

Discharged and ever

Wooden boards can decrease in size over time and dry. And this happens quite often.

Advice:

1. When repairing a wooden floor in an apartment or house, if the coating planks fumbled, it is necessary to fully replace them with new ones. Because the old can already be repaired. It is recommended to do, even if the damaged floor section has a small size.
2. If the area of \u200b\u200bdamage is large, then the wooden floor is recommended to be completely rebuilt.

Gaps in a wooden floor

The reason for the appearance of the gaps in the floor is usually the difference in humidity. Unfortunately, this process is almost impossible to exclude. Because humidity changes not only when changing the temperature, but at different times of the year. To soften the impact of this phenomenon, it is recommended to use special air humidifiers. These devices will help maintain moisture in the room at about the same level.

If the gaps appeared, then the parquet need a repair. The volume of work in this case depends on the location and size of the slot. If it is located approximately in the middle of the floor and its width is not more than 5 millimeters, the sequence of action during repair may be as follows:

1. Take a sharp and subtle item. Clean the gap with it.
2. Putty or mastic sprinkle a gap. For the preparation of the mixture, you can use birch, beech or oak sawdust, which should be mixed with joinery glue.

If the slit is width more than 5 millimeters, then the repair can be carried out in the following way:

1. Make a slit little deeper.
2. Take the chisel and push the edges with it.
3. If necessary, also clean the edges.
4. Cut from the tree insert and lubricate it with a joinery glue (you can apply mastic).
5. Then place the insert in the slot.
6. Place of repair is well sand and covered with a varnish for the floor.

Space plates

Wood planks can be flawed for many reasons. These include:

1. Using bad glue.
2. Increased humidity indoors.
3. The use of low-quality mastic.
4. Violation of the main technology when installing the floor.

Methods for solving this problem largely depend on what basis parquet was laid.

So, if the base is concrete, then the sequence of repair is as follows:

1. Clear sockets of planks from dust, dirt, garbage, as well as from old glue or mastic.
2. The basis is primed and dried.
3. Apply a new glue on the bar (you can apply mastic).
4. Glue a wooden bar into place.
5. When repairing it is not necessary to use new mastic. Suitable and old. To do this, it must be preheated until it becomes viscous.

If the parquet was laid on a wooden base, then the sequence of repair is as follows:

1. Clean the slots of the planks and wrap in glue.
2. Put the planks back and nail them.
3. Cut the nails and hts and hide under the surface of the plank.
4. The recess that will remain should be smeared with sawdust mixed with joinery glue.
5. When the place is dry, it needs to be seized and covered with a thin layer of varnish.

Pole cycle

Cyclic is one of the best ways to repair a wooden floor, but the price of this type of work is quite high. Therefore, you should first understand whether such costs are justified in your case. The cycle is beneficial only when parquet is worn evenly over the entire surface, and this happens rarely. Considering the high cost of cycle, before starting work, you need to make a estimate for the repair of wooden floors.

Do not pursue a cyclical in the following cases:

1. Severability, dismissed from moisture or crevices appeared in it.
2. From the basic coating there is evaporation or in the room there is an increased humidity.
3. On the surface of the wooden floor there are noticeable irregularities and potholes.
4. In the most worn place from the top of the slats, less than five millimeters remained to the screw.
5. Moved pest - bug-tree.
6. On the surface of the coating there is rot.

For cycles, the following tools are needed:

1. Drum grinding machine.
2. Angle grinder.
3. FlatSheliform tool and 2-3 disks to it.
4. Wooden floor varnish.
5. Industrial vacuum cleaner.
6. Puttlecular mixture for parquet.

Wiring must withstand the load from the tools. Otherwise, it makes no sense to spend the cyclove.

The sequence of actions during the cycle is as follows:

1. Release all possible furniture, remove the plinth and thoroughly spend the floor surface.
2. Twice to process the floor with a skin number 40.
3. Remove the remaining spots of varnish. This is done with the help of a corner car.
4. Remove all varnish in the corners.
5. Once again, overlook the surface of the wooden floor with a plane oarsal machine.
6. Mix the base of putty for the wooden floor.
7. Then the spatula is applied to the entire surface.
8. After drying, to process the floor with skins No. 60-70.
9. Using a roller to cover the floor with varnish.
10. After drying, treat the coating of the skin №11-120.

Floor Restoration

Recommendations:

1. Restoration can be performed on the entire surface of the wooden floor or partially. If there is no experience in conducting such works, then it is best to hire a specialist or at least get the recommendations of the technologist.
2. Whatever restoration work is carried out, at the end, the cyclove is performed, seelings of the slots and the alignment of the plane oarsal tool. Also, the finish coating is applied. Most often restoration is required if the floor is repaired in a wooden house.
3. If the damage appeared on the road art fleet, then it is better to hire a specialist for restoration work. Only qualified wizards will be able to return a unique parquet pattern.
4. If only part of the parquet floor is spoiled, then only a partial restoration is usually performed. At the same time, spoiled strips are removed and replaced with new ones. If this material is no longer available, then the drawing or ornament is restored on spoiled boards.

Wooden floor color has changed

Wooden floor can change color under the influence of sunlight. Moreover, various wood breeds in different ways react to ultraviolet. So, the smaller the material of the ripening time, the faster it becomes dark. For example, quickly darkens cherry. In any case, it is possible to delay the color of the wooden board by proper care. Care recommendations are as follows:

1. Do not cover the wooden floor of the carpet immediately after it is laid. You need to give him some time so that it is ripe.
2. If water hit the parquet, then you can not hesitate with its removal. The faster the moisture is eliminated, the better. If the planks were damaged, they should be replaced.
3. Try to operate the wooden floor correctly. It will cost much cheaper than regular repair by the forces of qualified specialists.
4. All wooden floor defects are usually manifested after a while. They are to some extent changing the appearance of the coating. Correct this will help the squabble.

In order for the wooden floor to listen to as long as possible without repair, the following recommendations should be performed:

1. Periodically rub the floors with a polyroller.
2. Put an air humidifier indoors.
3. Stick felt overlays on the legs of chairs, tables and other heavy items that can move.

Wooden Floor Repair Tips: Video