Repair of plastic windows with their own hands. How to repair plastic windows

Over the past 10 years, almost all people managed to equip their housing with plastic windows. Many of them even managed to change not one manufacturer's company due to low quality materials or possible damage. Therefore, the issue of repairing plastic windows is so relevant today. It is it that we will consider in our today's article.

Content

Repair of plastic windows with their own hands

To date, the production of plastic windows is engaged in a huge number of companies. And with such competition it is quite obvious that the products should be as high as possible. Despite this, even the high-quality PVC windows eventually begin to break out and require adjustment, and sometimes even repair. And to get rid of yourself from the extra costs, you can repair PVC windows with your own hands.

Required tools

In order to perform almost any windows repair, you may need appropriate tools and devices. Their list can be briefly described as follows:

WD-40 tool.
Pliers.
Crosshead screwdriver.
A complete set of star-shaped nozzles.
Hex key for 4 mm.

One of the most important elements for repair and adjusting PVC windows is a hex key, which is often performed in the form of the letter "G". It is he who is suitable for most popular windows installed in homes.

Repair of the Pen Plastic Window

Often there are problems that relate to the window handles. You can select the most frequent:

backlash handles;
jamming;
jealous;
full failure.

In the case of the back of the handle, everything is not so scary. In order to forget about the existence of this problem, you just need to tighten the corresponding mount.

This task is performed as follows:

Find a rectangular laying under the handle.
Patty it and check 90 degrees to the side.
Two bolts in front of you, which should be thoroughly tightened.
Take a cruciform screwdriver and perform the necessary work.
Hide the whole mechanism. Work is done.

If such a nuisance happened that the handle on your PVC window or door broke, you will have to replace it. Works are performed in this way:

Put the handle to the open position.
Turn a rectangular overlay 90 degrees.
Turn the bolts that you will see under the overlay.
Remove the broken old handle.
Install the new item in the reverse order.

If suddenly you noticed the jamming of the handles on the windows, or the fact that it does not reach the end of its position, it can mean different problems. Here are the most obvious:

the need for cleaning and high-quality lubrication;
the need to weaken clamping on sash.

You need a little weaken the mounting of the handle on the sash, disassembled it according to the scheme described above. If it does not help, then dismantle the handle, take the vacuum cleaner or the brush, and clean the entire mechanism from pollution. All process, then lubricate with machine oil. You can, of course, use and all the well-known WD-40, especially since its tube is very convenient for our problem.

When you noticed that the handle of your window is simply jammed, it can mean problems:

Freezing. From the compression of the design in the cold, the block can lead to such trouble.
Sharp movements when using the handle.

In order to correct the problem, you need to adjust the special sash on the side of the window so that it is in the smooth vertical position. So you can resume the normal work of the handle. Check if the sash is free of place, when closing the window. If not - you need to fix a little mechanism with a screwdriver. It is easy, and you will probably cope with such a task.

Repair of plastic windows

Often, the main problems that suggest the ideas about changing windows are in their fittings. She begins to close badly, skip third-party sounds, or even worse - cold. Therefore, the repair of the mechanism of plastic windows is also a very relevant issue.

Repair of plastic windows on their own

To begin, it should be said that every year you need to conduct preventive check of windows to avoid possible breakdowns. This is especially true of our country, because the temperature in winter we have almost critical, and in the summer - incredibly high. By checking, the voltage in the accessories will be reduced, and the result will be a long life of their operation.

Elimination of the problem is quite feasible with your own hands, especially since the prices of PVC windows really bite.

Getting to work:

Find oval cylinders that are located on the end of the sash. This is a pin or eccentric, as it is more convenient.
On the frame itself, you will find the response hooks created in order to go there the sash and when turning the handle, pressed to the frame itself.
In order to perfectly configure the mechanism, you need to scroll the eccentric or move the retaliatory hooks, after which you check.

If your task is adjusting the correct closing of the sash, the order of work is as follows:

Find the protruding part of the eccentric.
Turn it so that the process takes place towards the internal windows, if you need to tighten it. Accordingly, if necessary, we turn into the other way.

Varieties of eccentrics

Performing repair and adjustment of plastic windows, you may encounter the fact that the trough will look like you expected to see them. It simply explains: different manufacturers this element can be adjusted in different ways. The most popular ways to adjust are as follows:

rotate eccentric using pliers;
eccentric is discharged from the surface of the end, after which it scrolls a bit. For the removal of the pin, you can use PASSATIJ;
rotate the slot with a flat screwdriver, which is available on the pin.

Make all adjustments very carefully to accidentally damage the mechanism.

Work with the return part

Such a surprise may occur that the cylinders will not be able to configure. It does not matter, and from such a position there is a way out.

In this case, you will need to take the hex key, which should be corrected by the response of the mechanism. It is attached with two bolts, and if you weaken them, the hook will be free for easy movement. Naturally, carry out such adjustment and repair of plastic windows, the photo will help you like anything else.

You can read the work on strengthening or weakening the clamping effort made.

Configure side with canopies

If you have installed windows that have ventilation mode, and just in it is the problem, there is also a certain procedure that will allow you to produce high-quality repair of plastic PVC windows.

Remove the so-called casing cap, which is made of plastic. It is located on the lower canopy.
In the canopy you need to find 3 bolts. 2 of them will be noticeable, and one is a bit hidden.
The hidden bolt is regulated by a hex key, and with it and it is possible to adjust the position of the sash relative to the frame.
If you need to adjust the clamping effort, you will need to adjust the bolt, which is located perpendicular to the plane of the window itself. Tune it when the sash is in a closed position.
Twist the clockwise key to enhance the pressure, or against it for its attenuation.

As for the top of the sash, its mount is not carried out on a canopy, but on the so-called scissors. To adjust it, follow these steps:

Open the window sash.
On the side end you can see the clips of the block, or a special lever. It is necessary to click on it.
At a time when the block will be in the clamping position, you should turn the window knob to the ventilation position.
You will notice that the sash came out of a special groove, after which it will freeze in a hanging position on the scissor mechanism.
You got to the head that adjusts the clamp of the sash on top.
Turning the head of the bolt, you can configure the clamping force. Make small turns.

Warm slopes on the windows

When the repair of the locks of plastic windows is over, you can think about other problems and difficulties that most people inevitably face, at one time have decided to install PVC windows.

Therefore, it's time to talk about the repair of slopes of plastic windows. Often, standard slopes are not the best choice, so they need to be insulated.

Reason for installation

There are several relevant reasons why people decide to establish new slopes or repair old on their plastic windows:

Extension of the service life of windows (in some cases up to 20 years).
Avoid darkening.
Reinsurance from the fading of windows.

When the installation of slopes is carried out

People who are engaged in the repair and installation of plastic windows, know how much time you need to properly install the windows, as well as to carry out the procedure for mounting the slopes. But we will cover this moment somewhat more.

One day will be quite enough to ensure that the windows are infused "after installation. After that, the windowsill is set. Providing its installation, you need to think about the fact that plastic is able to expand from temperature drops. Therefore, on the left and on the right side it is necessary to leave the gaps of at least 1 centimeter.

By the way, it is necessary to take care of the rear of the future windowsill, since it must be withstanding a serious weight. It is possible that during the operation of the window sill, which can last dozens of years, will not once again with the goal of washing windows, hanging curtains, curtains, etc. Therefore, the windowsill is established between supporting self-draws, as well as a part of the profile below. So you can achieve free maintenance of loads up to 100 kg anywhere.

Another useful tip concerning the windowsill belongs to its inclination. Any windowsill must be slightly tilted in the premises. All because in otherwise, moisture will be collected near the window, and this will inevitably lead to the appearance of fungus, mold and other troubles.

Installation of slopes

Installation work can be started. Here is a list of necessary operations:

Drill through wooden guide holes. The drill is required by 6 mm, and the depth of the holes should be from 50 to 120 mm.
Insert the dowel and sketch of 51 mm.
Tighten all the screws, and also set the hats until the middle of the rail.
Now, if you need to press or remove the rail to the slope, you can simply twist the self-tapping screws that have become adjustable.
Align all guides parallel to the frame itself. By the way, for this you do not need special devices, it will tell you even a specialist in repair and maintenance of plastic windows. You can do with an assessment for a visual appearance. Explain this necessity is very simple. Often the windows are installed with a slight tilt specifically. And if the windows in your house fell under the list of such, exactly installed slopes, will only emphasize their irregularities, and externally it will be more than noticeable.
Machine wedges under the rail, then pour the mounting foam there. So you can fix the rails. By the way, it is better to make a choice in favor of a summer foam, because it has more strengthening properties.
If you decide to install plastic slopes, they must be started at the frame for about 3-6 millimeters.
Next, shuffle the foam seam. If suddenly the plaster falls on the frame, do not worry, because after drying it, you will easily remove it.
The next step must be nailed to the guides of the J-profile, which will serve as a connecting. To secure it, it will be necessary to drive the brackets, approximately 1-1.5 cm. Step select from 10 to 25 centimeters.
In turn, that the C-profile lay down perfectly, the wall needs to work with the help of a plaster mixture that quickly solidifies.
Next, the formation of a foam seam. This is one of the most important points in the repair of slopes, so you need to be attentive. Apply foam uniform amounts. Form the foam seam by filling around 10-20 percent of the sub-window surface.
Heat the slopes with mineral wool, which also absorbs empty moisture. That is this way you get rid of the possibility of fungus.
Now you need to press the panel to the slats, after which they fix them with the help of an electrical plate. By the way, if you give a staple bracket under the tilt, they will create additional pressure by pressing the panel more securely.
Suffer plaster with a spatula.
Cut the corner of the C-profile with part of the internal type lock, then snap it into the j-profile hook.
After that, the corner must be kept using a hacksaw. So you will make seam invisible.
Everything is almost ready for overlapping decorative sealant. It remains to remove the room and plastic window elements.
Degrease the place of the joints with the help of suitable means.
Moisten the locations of the joints with water.
On perfectly clean windows, impose a sealant, which will close all existing joints.

As you can see, work is not easy, but if you know that the repair of windows PVC costs the cost of firms is not particularly low, it is possible and to master such a slight improvement personally, especially since the instruction more than in detail explains.

Repair of plastic windows. Video

Completing the conversation about the repair of windows, I want to reinforce all the described operations with a wonderful video tutorial. It is available to the topics of repairing the most popular problems arising from most PVC models.